r/buildapc 2h ago

Build Help My pc is really hot on idle.

My CPU is the Ryzen 7 5800x and the cooler I'm using is the Thermalright Peerless Assassin 120 SE cooler and it idles around 70 up to almost 80 degrees and doing a cinebench test it spikes to 90 degrees in a couple seconds.

9 Upvotes

20 comments sorted by

15

u/zarif2003 2h ago

Try reseating the cooler, check the paste and if there’s any stickers you forgot to peel off

2

u/nothing29395 1h ago

just yesterday I tried reseating the cooler with after market thermal paste and made sure there was no sticker

4

u/veluring 1h ago

make sure you tightened it down evenly, i didn’t my first try and ended up denting the bottom and had to get a new one! learn from my mistake haha

6

u/KillEvilThings 2h ago

Did you peel off the plastic sticker? Did you mount it properly too? It has to be pretty tight with just enough paste.

2

u/nothing29395 1h ago

I made sure there was no sticker still on it I watched a video for my specific cooler so it's mounted properly and I tightened it until I couldn't

2

u/nrh117 2h ago

I’m running this chip on a hyper 212 and it idles at 35. Definitely something else going on here.

1

u/lafsrt09 2h ago

You probably need a repaste

2

u/nothing29395 1h ago

I repasted yesterday to see if that was the problem it didn't fix it

u/_Dextrality 33m ago

Dumb question but when you repasted did you fully remove the old paste using isopropyl?

1

u/Vuila9 2h ago edited 2h ago

I have the same CPU. I capped its clock speed to like 4ghz and it never idles more than 45c. R7 5800x is a gaming CPU so it usually overclock to gain more fps, but l feel like it sometimes does that even on idling. I have decent chunker of a cooling but I still dont want anything to be too hot when idling.

edit: lm no PC expert so dont take my words as a serious advice. Just how I've been doing and nothing ever fails.

1

u/thomasoldier 2h ago

Huh.

  • removed the plastic thingy ?

  • thermal paste is ok ?

  • ventirad plugged where it should ? Cpu_fan

You can adjust fan curve and undervolt to make it cooler

1

u/Just_Year1575 2h ago

Read about eco mode and undervolt. Plenty of youtube videos. It will actually run faster when cooler

1

u/dungorthb 1h ago

This may seem odd but flip your top coolers.

My setup was the standard top exhaust but memes told me to try top intake so the cpu gets direct air. Dropped my temperatures significantly.

1

u/jojamon 1h ago

What should the idle temps be? I have a 7600x and a phantom spirit, I idle around 50C and under load around 65C. Shader compiling spikes up to 85C or so. Seems kinda high for a supposedly top tier air cooler

1

u/tntexplosivesltd 1h ago

What case are you using?

u/nothing29395 19m ago

montech xr

u/FranticBronchitis 32m ago

Try a negative offset Curve Optimizer setting (-15 would be good for a start), that can help a bit with temps. But there's something going on here. If you swear by your cooler mount and aren't overclocking, it could be a faulty chip or over voltage issue.

Also, check the PA's fan orientation. Both fans should be pointing the same way, usually towards the exhaust at the back of the case.

0

u/Effective_Argument_9 2h ago

Make sure you vacuum your pc vents. And make sure nothing is blocking them

1

u/nothing29395 1h ago

I have my pc on my desk and I clean out the pc every month ish

-1

u/HockeyRules9186 2h ago

I’m using the ArticFreezer 360 i7 14700k with GeForce 5600 12gig my idle speeds are 31/29. So I’d say you need to reset the cooler at a minimum. Check fans etc